Latest development from me.......

It's the home for everything eTap2HW on ShadowMusic

Moderators: Iain Purdon, dave robinson, George Geddes, David Martin, ecca

Latest development from me.......

Postby ecca » Mon May 19, 2014 4:14 pm

I have made a PCB for the Automation eTaps. This incorporates Piet's interface circuitry and Johann's smoothing components.
Its manner of interfacing with the eTap PCBs is simplified. No wiring changes whatsoever are required if adapting an existing eTap for Automation use.
The FV-1 module is plugged out and the 16 pin lead from this pcb plugged in, in its place. The FV-1 module is then plugged into the new PCB.
It then connects piggyback to the Arduino unit underneath and the Adafruit display on top. The display will require spacing to clear the FV-1 module.
There is also an 8 way connector which brings out the 5 volt supply, the serial connection to the display and also the midi Tx/Rx connections.
The power for the Arduino is taken from the original board and smoothed using Johanns inductive/capacitive circuit as previously shown here.
Because of its connection manner there was an anomaly with the clip LED inasmuch as there was a small standing voltage left across it . This has been corrected by fitting a 6 legged opto-isolator.
The resistors are all SILs.
Pictures here.......

https://app.box.com/s/moshor1hvrvy3547720o
User avatar
ecca
 
Posts: 3554
Joined: Sat Sep 12, 2009 8:25 pm
Location: Finca de Pelsall
Full Real Name: Eric Blossom Thacker

Re: Latest development from me.......

Postby David Martin » Fri May 23, 2014 8:38 am

So... Can you upgrade existing valve preamp models?
David M
User avatar
David Martin
 
Posts: 1753
Joined: Tue Sep 08, 2009 4:48 pm
Location: Lincoln
Full Real Name: David Martin

Re: Latest development from me.......

Postby ecca » Fri May 23, 2014 9:00 am

Yes, but I have to try to get it all into existing enclosures. it's not too far off now.
User avatar
ecca
 
Posts: 3554
Joined: Sat Sep 12, 2009 8:25 pm
Location: Finca de Pelsall
Full Real Name: Eric Blossom Thacker

Re: Latest development from me.......

Postby David Martin » Fri May 23, 2014 10:57 am

Keep me in the loop... the loop... the loop...
David M
User avatar
David Martin
 
Posts: 1753
Joined: Tue Sep 08, 2009 4:48 pm
Location: Lincoln
Full Real Name: David Martin

Re: Latest development from me.......

Postby Holperi » Fri May 30, 2014 3:59 pm

Ecca,

To fully understand your development I like to ask if you by "Johan’s inductive/capacitive circuit* mean the same circuit as in eTap2hw Bulletin 3 “Power Supply Noise Filter for Arduino Automation” written by Steve Mitchell?

Regards
Rolf
Holperi
 
Posts: 1
Joined: Thu Dec 13, 2012 8:51 pm
Full Real Name: Rilf Holmberg

Re: Latest development from me.......

Postby ecca » Mon Jun 02, 2014 4:14 pm

Rolf - yes.
User avatar
ecca
 
Posts: 3554
Joined: Sat Sep 12, 2009 8:25 pm
Location: Finca de Pelsall
Full Real Name: Eric Blossom Thacker

Re: Latest development from me.......

Postby Strummer » Fri Jun 13, 2014 2:15 pm

ecca Good afternoon,

I have left a message under "Echo Machines" basically i am asking the price etc of your E-Tap 2HW. Can you let me know asap as i am trying hard to resolve the echo problems i have. I use VOX AD 30 VT's and a VOX AC30 CC2 al valve.

Thank you for reading this, I look forward to your response.

Arthur/Strummer
Strummer
 
Posts: 171
Joined: Mon Oct 25, 2010 4:16 pm
Full Real Name: Arthur Howard

Re: Latest development from me.......

Postby ecca » Sun Jun 22, 2014 8:09 pm

I've made another PCB for the eTap unit.
It interfaces the LCD display to the Arduino and FV1 module.
I've made this PCB the same width as the display itself by putting the components on one side and the LCD and switches on the other so it will go into my
normal enclosures that I use for the valve Eccamatics.
There is a contrast adjustment and a terminal block for midi connection if wanted.
There are 2 centre biased switches that do the up/down, left/right functions . ( less holes to drill ) and a button to store.
Connection is via an 8 way PCB connection suitable for IDC connection. This marries up nicely with the pcb I made a couple of months back.
The LCD itself plugs in and can swapped for a RGB colour type if wished.

https://app.box.com/s/02hwst9b7ioz669q2hcq
https://app.box.com/s/pqj83k1cnvexj7eg2r3d
User avatar
ecca
 
Posts: 3554
Joined: Sat Sep 12, 2009 8:25 pm
Location: Finca de Pelsall
Full Real Name: Eric Blossom Thacker

Re: Latest development from me.......

Postby rogera » Sun Jun 22, 2014 8:18 pm

Neat work Ecca :thumbup:
User avatar
rogera
 
Posts: 1021
Joined: Wed Sep 16, 2009 1:06 pm
Location: South West
Full Real Name: Roger Allcock

Re: Latest development from me.......

Postby GuitarPhil » Mon Jun 23, 2014 1:08 am

That looks like a very neat unit, Ec. It should also fit in a 1U rack panel, by the looks of it.
User avatar
GuitarPhil
 
Posts: 258
Joined: Tue May 11, 2010 11:32 pm
Location: Northern Ireland
Full Real Name: Philip Hawthorne

Next

Return to eTap2HW Forum

Who is online

Users browsing this forum: No registered users and 1 guest

Ads by Google
These advertisements are selected and placed by Google to assist with the cost of site maintenance.
ShadowMusic is not responsible for the content of external advertisements.